Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Paver Driveways in San Francisco: What the Job Actually Involves
Paver driveways in San Francisco typically cost between $8,260 and $21,240, and most of ours are finished in five to eight working days once the base is proven. The work is a full dig-out: we remove the old slab, re-establish slope, compact a base, and lay pavers on a tight, drained plane. In San Francisco, that plane often has to shed water toward the street with only inches of fall to spare, and on an alley or hillside lot the base prep is where the real money and the real hours go. Call (866) 320-2646 for a free estimate.
How we build a paver driveway, stage by stage
Stage 1: Site visit and layout (day one). We measure the driveway, note the garage door head height, check where fog-driven moisture already pools, and measure the fall to the street. You decide the paver format and color, and you tell us whether the driveway also needs to clear a turning car or a tandem park. This is the day the pattern gets locked in.
Stage 2: Demo and haul-off (days one to two). We break out the existing slab, old pavers or asphalt and haul it away. On San Francisco hillside lots a lot of that material comes out by hand because there’s nowhere to put a bin and the street is narrow. We also uncover anything buried: an old clay drain line, a gas stub, a foundation footing that pokes into the right-of-way. Those get flagged and priced before we move on.
Stage 3: Base, subdrain and compaction (days two to four). This is the stage that decides whether the driveway lasts. We excavate to depth, lay a compacted aggregate base, and on the fog-belt side of the city we run a perforated subdrain under the base to catch what comes down the hill. You don’t decide anything here except to approve a change if the subgrade turns soft. We compact in lifts and check the slope with a level.
Stage 4: Edging, sand and pavers (days four to seven). We set edge restraints in concrete, screed the bedding layer, lay the pavers and cut the borders to the garage apron and the driveway mouth. On a driveway constrained by a neighbor’s wall and a garage on the same lot, cut tolerance runs tight and we account for it in the labor. Then we sweep in the joint sand.
Stage 5: Compaction, seal decision and walkthrough (days seven to eight). We run a plate compactor over the finished field, leave a cure window for the joint sand, and walk the driveway with you. You decide whether to seal now or wait a season. That’s the whole job, and it’s part of a full Driveway & Pavers in San Francisco scope when the driveway also needs a front walk or an apron.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The paver options you’ll actually be choosing between
A paver driveway is a spec job, and the choices you make on day one drive both the look and the durability. Here’s where the real decisions sit:
- Concrete pavers (the default). The standard choice for San Francisco driveways, and the format everything else is compared against. Durable, repairable, and the joint sand gives you a drain channel. You’ll usually pick from a manufacturer’s own catalog rather than an open market. We work with Belgard and similar lines where the color and size match the lot.
- Clay or brick pavers. Warmer, denser, and they take the fog and salt air well because they don’t fade. More expensive per square foot and slower to lay. Suited to an older Edwardian or Victorian where the frontage has some architectural character to match.
- Permeable pavers with open joints. These let rainwater through into the subgrade, which matters on a lot that has no storm drain to send water to. They cost more in materials and need a deeper base, so the savings are in drainage performance, not price.
- Formats and borders. A running bond or herringbone field with a soldier-course border is the standard look and is faster to lay. A full herringbone field looks better and costs more in cut and labor. An ashlar pattern on a rectangular paver is the middle ground.
- Color and finish. A tumbled or sandblasted face hides drive-lane scuffs and general wear better than a smooth face. On a steep San Francisco driveway, a smoother face can be slick when wet, so a textured finish is the safer pick.
What Paver Driveways cost in San Francisco, CA
Paver driveways in San Francisco run $8,260 to $21,240 for the standard scope, and a few factors push a job toward one end or the other. The biggest movers:
- Square footage. A compact city driveway of 240 – 350 square feet lands near the low end. A lot that opens onto a garage plus a tandem park can run 600 – 800 square feet and land in the high range.
- Existing condition. A thin old concrete apron comes out cheap. A thick, reinforced slab on a hillside block, or old pavers with an unstable base, adds demo and haul-off time.
- Material grade. A standard concrete paver in a running bond is the base price. Herringbone in clay brick, or a full permeable system with a deeper subgrade, moves the number up.
- Access. A lot where a bin can park on the street is easy. One where everything has to come out by hand up a narrow alley or down a hillside stair adds labor, and that shows up in the range.
- Drainage. Adding a subdrain and a catch basin, or engineering a fall to the street where the grade doesn’t cooperate, is its own line item.
A written estimate from us breaks out demolition, base, materials, edging, drainage and labor line by line, with the number you see being the number you pay. It does not typically cover permit fees if a street-use or encroachment permit turns out to be required, or structural work if the base reveals a failed retaining wall or footing.
See the difference
Before
After
Before
After
Before
AfterWhat San Francisco itself does to a paver driveway job
The first thing to know is that this is a hillside city built on some of the densest, oldest lots in the country. A driveway here is often a 250-square-foot strip that has to shed water down a grade and under a garage on the same narrow lot, so the base and the fall are the whole game in a way they aren’t in a flat suburb. The next is the housing stock: a lot of what we’re working on sits on 1880s – 1920s Victorian and Edwardian row houses with brick foundations, or 1950s – 70s stucco-over-wood blocks, and some of that older stock has had a soft-story seismic retrofit that changes where you can dig and what attaches to the driveway.
Then there’s the fog and salt air. On the west-side hills, that damp makes standard joint sand and fasteners degrade at a rate a contractor from a drier city wouldn’t expect. We spec stainless hardware and galvanized or corrosion-resistant edging as a matter of course, because the fog belt corrodes standard fasteners within a fraction of the normal lifespan. It’s why we don’t skimp on the edge restraint.
Permitting is a separate reality. Any project that touches the public right-of-way in San Francisco can run through a discretionary approval, and the review isn’t quick. We plan the driveway work to match what’s actually being built on the lot, and the paperwork gets pulled before a base is cut. While we’re here, homeowners often pair this with Garage Conversion ADU in San Francisco work, since the driveway apron and the conversion often move together. The work is part of our Driveway & Pavers service, and we cover the whole of San Francisco.
Serving San Francisco, CA – Our Local Coverage Area
We serve San Francisco and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Paver Driveways in San Francisco
Most paver driveways in San Francisco are finished in five to eight working days, with base prep and drainage taking the longest stretch and the paver lay itself running two to three days. Wet weather can push it, and hillside access can stretch demo. Call (866) 320-2646 and we’ll give you a schedule based on your actual driveway.
A paver driveway on private property often doesn’t need a building permit, but anything crossing the public right-of-way or changing the curb can. The rules are enforced by the city, not by us, so we look at your lot and tell you before we quote. Call (866) 320-2646 to walk through your driveway.
Yes, in the vast majority of cases a paver driveway is a surface and base job, and we don’t touch the house or the utility lines unless the dig uncovers a failing pipe or footing. If we do hit one, we stop and price it before going further. Call (866) 320-2646 for an on-site look.
Paver driveway installation in San Francisco runs $8,260 to $21,240, with the number set by square footage, existing slab condition, material grade, access and drainage. The written estimate itemizes each of those. Call (866) 320-2646 and we’ll price your driveway for free.
Every paver driveway we install is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction. Call (866) 320-2646 and we’ll put it in writing before you sign anything.
Get a free estimate for your paver driveway
We’ll come to your San Francisco address, measure the driveway, check the fall and the base, and give you a written line-item estimate with a firm number and no change orders. A live person answers the phone around the clock, so there’s no voicemail black hole. Call (866) 320-2646 to schedule your free estimate, and we’ll bring the paver samples with us.
Written by the team at Groundwork Construction Co..