Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Tiburon, CA: What It Costs and How It Works
An iron fence in Tiburon runs $3,500 to $9,000 for most hillside lots, with the typical project landing in five to eight weeks from contract to final inspection. That figure covers layout, footings, fabrication, installation and finish, and it assumes a normal residential run of 80 to 150 linear feet. The number moves most on access, grade and the gate hardware you choose, not on the iron itself. Call (866) 320-2646 to set up a free on-site estimate.
How the Iron Fence Work Actually Runs, Stage by Stage
A lot of fence quotes are written from a car window. Ours aren’t, and the schedule reflects that. Five stages, each with a decision point where you’re in control.
Stage 1: Site survey and access plan (week one, about two to three hours on site). On the winding streets above Main Street and around Belvedere, the survey is less about the fence and more about how material reaches it. We measure the run, check grade changes, and figure out whether a truck can back into the driveway or whether iron panels and concrete bags get walked in. You’ll confirm the property line and decide where the fence starts and stops.
Stage 2: Design and product selection (one to two weeks). You pick panel height, picket spacing, finial style, post size, finish and gate type. This is the stage where a security-focused design gets locked in: do you want vertical pickets at 4 inches on center, or a tighter 3-5/8 inch spacing that closes the visual gap? Do you want an arched top on the street elevation? This is also when we confirm whether any portion is set back under a full Fence Installation in Tiburon plan, since iron run alongside a new wood or retaining structure needs to be laid out together.
Stage 3: Layout and utility check (a few days). Before anyone digs, we stake the run and call for utility marking. On older Tiburon lots with unpermitted past work, we confirm what’s under the ground and where the property line actually sits relative to the fence you want.
Stage 4: Footings and post setting (two to four days, plus cure time). Posts get set in concrete footings sized to the fence height and local wind exposure. Because so much of Tiburon is built into slopes, sections on grade changes usually mean stepped panels rather than raked panels, and that gets decided here. Holes that can’t be machine-dug on a tight lot get dug by hand, which is slower and shows up in the quote honestly.
Stage 5: Fabrication, install and finish (two to three weeks). Iron sections get fabricated to measured dimensions, delivered, hung on the posts, and finished with your chosen coating. Gates get mounted and swing-tested. Final walkthrough covers post alignment, gate latches, finish coverage and touch-up. You sign off, and the 730-Day Done Right Promise covers the work from that day forward.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Iron Fence Options You’ll Choose Between
Most homeowners land on one of a few paths. Here’s the honest trade-off of each.
- Wrought iron (solid bar stock). The heaviest and longest-lived option, and the one that fits Tiburon’s salt air best when finished correctly. Costs at the top of the range. Suits estate entries and long street-facing runs.
- Steel with a powder-coat finish. The most common choice for residential iron fencing. Powder coating resists rust far better than paint-on finishes, and touch-up is straightforward. Mid-range pricing. Good all-rounder for most lots.
- Aluminum “iron-look” panels. Lighter, rust-resistant and less expensive, but a different product entirely, so we route that conversation through our separate aluminum page rather than pretending it’s the same thing.
- Finish options. Black is standard and hides touch-ups. Bronze and dark green cost a bit more and look sharp against stucco. Bare or painted finishes cost less upfront but need recoating sooner under fog-belt moisture.
- Gate and access hardware. Manual latch, self-closing hinge, or a rolling-code keypad that lets you change the entry code without rekeying. Rolling-code is the right call for shared driveway or alley access where codes get passed around.
What Iron Fence Costs in Tiburon, CA
Most residential iron fence projects here land between $3,500 and $9,000. Five variables push a job toward the low or high end.
- Linear feet and height. An 80-foot run at 4 feet tall sits near the low end. A 150-foot run at 6 feet with two gates sits near the high end.
- Grade and slope. Flat runs price simply. Stepped runs on a Tiburon hillside require more posts, more footings and more fabrication hours.
- Access. If a truck can’t reach the site, hand-carry and hand-dig hours add real money. This is often the single biggest line item on a hillside lot.
- Gate count and hardware. Each gate is its own fabrication and hardware job. Keypad entry, self-closers or a second pedestrian gate push the number up.
- Permit scope. A street-facing run on a slope may need a permit and inspection. Interior side-yard runs usually don’t.
Your written estimate itemizes posts, panels, footings, gates, hardware, finish and permits, with the labor broken out. Expect a line-item number you can compare against another bid without guessing. Promotions include $1,000 off projects over $10,000 and 0% financing for 18 months, both of which matter on longer runs.
See the difference
Before
After
Before
After
Before
AfterWhat Tiburon Homes Specifically Do to This Job
Tiburon’s housing stock is the real driver. Near downtown you’re often working on early-1900s shingle and stucco cottages with tight side yards and old property lines. Up the hills you’ll find mid-century and contemporary homes with cantilevered decks, and iron fencing has to step with the grade rather than follow a flat line. Salt air off Richardson Bay and the bayfront corrodes fasteners, hinges and finish faster than inland Marin, which is why we spec corrosion-resistant hardware as the default here rather than an upgrade. Winter rain and fog-belt moisture on south- and west-facing exposures mean any painted finish needs proper prep and a recoat schedule. On the steep streets above Main Street and around Belvedere, the access reality described earlier applies to iron fencing as much as anything else: panels and footings get staged around a hairpin driveway before anyone prices the iron.
Serving Tiburon, CA – Our Local Coverage Area
We serve Tiburon and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions: Iron Fence in Tiburon
Residential iron fences here run $3,500 to $9,000, with hillside access and gate hardware as the biggest swing factors. Call (866) 320-2646 for an exact quote; estimates are free and on site.
Plan on five to eight weeks from signed contract to final walkthrough, with about two to three weeks of that being fabrication time off site. Access constraints on a steep Tiburon lot can add a week. Call (866) 320-2646 to talk through your timeline.
Interior side-yard and rear-yard fences usually don’t need a permit, but street-facing runs and any fence on a significant slope often do, and coastal-zone lots can bring extra review. Call (866) 320-2646 and we’ll confirm with the town before you commit.
Not on our jobs. The written estimate is the number you pay, with 730-Day Done Right Promise coverage behind the workmanship. If something surprising shows up underground, we stop, show you, and write a change order before any work continues. Call (866) 320-2646.
Yes, in the vast majority of cases, because fence footings are shallow and the run gets laid out around utilities after marking. Where a footing conflicts with a buried line, we offset that post rather than dig near it. Call (866) 320-2646 for a site visit.
Every iron fence project we install is covered by the 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction. That covers installation and finish issues we control. Call (866) 320-2646 for the written warranty terms.
Yes, we work throughout the 94920 ZIP and the surrounding area, including Tamalpais-Homestead Valley, Corte Madera, Mill Valley and Larkspur. Read more on our Tiburon service page, or call (866) 320-2646.
Get a Free On-Site Iron Fence Estimate in Tiburon
Call (866) 320-2646 and a live person picks up, day or night. We’ll schedule a free on-site visit, walk the run with you, talk through gate hardware and finish, and send a written line-item estimate. No pressure, no vague numbers. If you’re pairing the fence with a patio or hardscape, our Patios, Walkways & Pool Decks in Tiburon team can quote it alongside. And if the project includes a guest unit, our ADU Design & Permitting in Tiburon work pairs naturally with the same layout planning. For the wider scope, see our Fence Installation service.
Written by the team at Groundwork Construction Co.