Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in San Bruno, CA
Metal Roofing in San Bruno is a full tear-off and re-roof job, not a weekend upgrade. Most homes need 5 to 9 working days from the first morning of demolition to final inspection, and the cost runs roughly $15,000 to $40,000 for a typical 94066 house. Call (866) 320-2646 to schedule a free on-site estimate and get a written, line-item number before anything gets ordered.
How we take a San Bruno roof from old shingles to standing metal
Metal doesn’t go over the top of what’s there. The old roof comes off, the deck gets checked, and the water barrier gets rebuilt before a single panel lands. Here’s the sequence we run, start to finish.
- Day 1 – Tear-off and deck inspection (1 to 2 days). We strip the existing shingles or tile down to the sheathing and walk the deck board by board. On the older post-war houses here, that’s where soft or delaminated plywood shows up. You approve any decking replacement in writing before we continue, and that’s the one line that can move the bid.
- Days 2 to 3 – Dry-in and flashing. New underlayment goes down, then the edge metal, valley metal, and the penetrations. Vent stacks, chimney surrounds, and the transition at the low slope get flashed by hand. Get this wrong and the roof will leak within one winter; the marine layer doesn’t forgive sloppy detailing.
- Days 3 to 6 – Panel set and fasten. Panels get laid to your chosen panel width and fastened on the correct pattern for local wind uplift. Long panels are run in full lengths where the roof geometry allows, which means fewer seams. You choose panel profile and color before this stage, not during it.
- Days 6 to 8 – Trim, ridge, and close-out. Ridge caps, gable trim, and the final fastener seals go on. We magnet-sweep the yard and driveway twice for stray screws, because a flat tire from a roofing screw is a bad way to remember a good roof.
- Final day – Inspection and walkthrough. The permit inspection gets called when we say the roof is ready, and we walk the finished roof with you. That’s also when the 730-Day Done Right Promise kicks in: if something’s not right, we make it right, in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The metal roofing options you’ll actually choose between
Most of the decisions on a metal roof come down to four things: panel type, metal, coating, and color. Each one trades cost against how it holds up under salt air and damp.
- Standing seam vs. exposed fastener panels. Standing seam panels hide the fasteners under raised seams, so there are no screw heads to back out or corrode over time. Exposed-fastener panels cost less but rely on hundreds of gasketed screws that need watching in coastal air. On a San Bruno roof near the fog belt, standing seam is the better long-run choice.
- Steel vs. aluminum. Steel is strong and accepts a wide range of finishes; aluminum resists salt corrosion better and never rusts. If you’re within a few blocks of the bay or ocean breeze, aluminum or a heavily coated steel is worth the upcharge.
- Coating and finish. A quality factory finish is what keeps a metal roof looking right through damp winters. The finish, not the bare metal, is the part that ages.
- Color and profile. Color is aesthetic and durability-neutral; profile affects wind performance and the look from the street. Choose the color before panels are manufactured, because cut lengths aren’t returnable.
- Panel width and seam spacing. Wider panels mean fewer seams and a cleaner line, but they flex more. Narrower panels handle irregular roof geometry better on some of the cut-up ranch plans around here.
If you’re already planning exterior work, homeowners often pair this with Window Replacement in San Bruno so the whole envelope gets sealed together, and some go further with Impact Windows & Doors in San Bruno for wind resistance.
What Metal Roofing costs in San Bruno, CA
Metal Roof Installation in San Bruno typically runs $15,000 to $40,000, depending mostly on roof size, panel type, and how much of the deck needs replacing. Here’s how that breaks down.
| Line item | Typical range |
|---|---|
| Metal roof installation (full) | $15,000 – $40,000 |
| Underlying roof repair found during tear-off | $400 – $1,800 |
| Full roof replacement reference (shingle) | $8,000 – $20,000 |
Four things push a metal roof toward the high end. First, square footage and roof complexity: hips, valleys, dormers, and multiple planes all add labor. Second, existing condition: soft sheathing, prior leak damage, or a second layer down means more tear-off and more deck work. Third, panel type and metal: standing seam in aluminum sits at the top, exposed-fastener steel at the bottom. Fourth, permit scope: seismic or structural upgrades that surface during inspection get added by change order, in writing.
Your written estimate lists tear-off, decking allowance, underlayment, flashing, panels, trim, fasteners, cleanup, and disposal. It doesn’t cover structural repairs hidden behind the deck, which is why we open up the roof before finalizing panel orders. Upfront pricing, no surprises. Call (866) 320-2646 and the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat San Bruno homes specifically do to this job
San Bruno’s housing stock shapes a metal roof job in ways it wouldn’t in a newer suburb. The Crestmoor neighborhood and the streets around it are dominated by post-WWII single-family homes, many built in the 1940s and 50s. The 2010 PG&E gas pipeline explosion triggered a mandatory seismic retrofit and rebuilding wave here, so you’ve got newer seismic-compliant structures alongside older homes that still need foundation bolting, shear walling, and chimney bracing. On a re-roof, that retrofit reality matters: the roof-to-wall connection and chimney flashing are where we often find the old work, and a metal roof’s heavier system puts more demand on that connection than asphalt did.
Then there’s the fog belt. San Bruno sits on the San Francisco Peninsula with cool, damp summers and steady onshore wind from the Pacific. That marine layer accelerates moisture intrusion and rot in exterior wood sheathing and trim, so proper flashing and weather-resistant detailing aren’t optional on a roof here. It’s also why 94066 permits and inspections go the way they do: strict on waterproofing and fastener specs, and digging near the former Crestmoor blast zone triggers PG&E gas line clearance procedures that can delay the job. Contractors working here need to know that before they schedule. We cover San Bruno and the surrounding Peninsula, and if your project grows past the roof, our broader Roofing in San Bruno work and our Roofing service line handle the rest of the scope.
Serving San Bruno, CA – Our Local Coverage Area
We serve San Bruno and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Metal Roofing in San Bruno
Most full metal roof installations here take 5 to 9 working days from tear-off to inspection, with a day or two of buffer for deck repairs or a slow permit inspection. Call (866) 320-2646 for a schedule built around your house.
Yes. A full re-roof requires a permit and a final inspection, and we pull it and meet the inspector on site. Post-2010 seismic rules mean the inspect can flag blocking or chimney bracing to correct, and we handle that in writing before it affects your price.
Almost always, yes. A metal roof is an exterior system, so plumbing and structural changes aren’t part of it unless the tear-off uncovers something failing. When we open the deck, we tell you what we find and quote it as a written change order – not a surprise.
It holds up well if it’s specified right. Aluminum or heavily coated steel, hidden-fastener standing seam, and stainless or coated fasteners are what keep a coastal metal roof from corroding early. A cheaper exposed-fastener system will show wear faster here than it would inland.
Manufacturer warranties vary by panel and finish, and every install we do is covered by our 730-Day Done Right Promise on workmanship. If it’s not done right, we make it right. Call (866) 320-2646 to walk through the options with a live person.
Get a free metal roofing estimate in San Bruno
Call (866) 320-2646 for a free on-site estimate on Metal Roofing in San Bruno. We’ll walk the roof, measure it, check the deck, and hand you a written line-item quote with financing options, including 0% financing for 18 months and $1,000 off projects over $10,000. Calls are answered by a live person, 24/7, with no voicemail. Start with one visit and one honest number.
Written by the team at Groundwork Construction Co.