Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in San Bruno, CA: What It Costs and When It Can Be Built
A chain link fence in San Bruno typically runs $3,500 – $9,000, with most residential lots landing in the $4,500 – $6,800 range for 150 – 250 linear feet of galvanized or vinyl-coated fence. Small jobs finish in one day; anything needing permit review takes longer. Call (866) 320-2646 for a free on-site measure and a written line-item quote.
How We Build a Chain Link Fence in San Bruno, Start to Finish
Chain link looks simple, and it is, but the job only holds up if the layout and the footings are right. Here is the sequence we actually run.
Stage 1: Property line verification and layout (day 1, 2 – 4 hours). Before a single post goes in, we confirm the boundary against your plat or a survey. San Bruno lots are often tight, and a fence set six inches onto a neighbor’s side is a problem nobody wants to discover after the concrete sets. You decide the exact run, gate positions, and whether you’re fencing all sides or tying into an existing fence.
Stage 2: Utility locate and dig (day 1 – 2, 4 – 8 hours depending on length). We call 811 for markouts. Around the Crestmoor area this matters more than most homeowners realize: PG&E clearance procedures near the old pipeline corridor can add days before digging is cleared, so we schedule the locate first and never gamble on it. Posts are set roughly 8 feet apart, in concrete, at a minimum 2 feet deep. You’ll see us on site deciding which posts fall on soil versus hardscape – that choice affects footing depth and cost.
Stage 3: Concrete cure (24 – 48 hours). We don’t hang fabric the same hour we pour. Terminals and gate posts take the most load, so those cure first and longest.
Stage 4: Rails, tension wire, fabric, and gates (day 2 – 3, 3 – 6 hours). Top rail, tension wire at the bottom for anything taller than 4 feet, then fabric stretched and tied at every post. Gates get their hinges and latches set for level swing and proper latch alignment. This is the stage where a cheap install shows: sloppy tension means sagging corners within a year.
Stage 5: Walkthrough and cleanup (same day). We walk the run with you, open and close every gate, check tension by hand, and haul off all spoils and packaging. Total timeline: one day for a standard side-and-back yard, two to three days once permits or gas-line clearance are in play. Choose the fence height early (4, 5, or 6 feet matter for code and cost) and decide on coatings before we order, since lead times shift with color and gauge.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between for Chain Link
Chain link isn’t one product. These are the real forks in the road, and what each one costs you in money or longevity.
- Galvanized vs. vinyl-coated fabric. Bare galvanized steel is the cheapest and handles weather fine, but it goes dull gray. Vinyl coating in black or green costs more and holds color, which matters on the front run facing the street.
- Gauge and mesh size. 11-gauge is standard; 9-gauge is heavier and worth it on a run that takes kids, dogs, or ball impacts. Smaller 2-inch mesh blocks small pets better than the standard 2-inch diamond in most residential grades.
- Height: 4, 5, or 6 feet. Most San Bruno yards run 4 or 5 feet; a 6-foot run costs more per foot and may bump into local height limits depending on placement, so we confirm before ordering.
- Line posts: steel vs. schedule 40 pipe. Standard steel posts handle residential loads. Schedule 40 on the terminals and gate posts is the upgrade that stops a swinging gate from dragging after a few seasons.
- Top rail and tension wire. A tension wire at the bottom keeps the fabric tight against dogs and wind. Cheap out and the bottom edge bows.
- Gates and hardware. Walk gates, double drive gates, self-closing latches. Hardware grade is where most budget fences fail first; the forging matters more than the fabric.
- Privacy options. Slats or a screen insert turn chain link into a sight barrier without losing airflow. We mention them here, but the privacy fence itself is a different job and has its own page.
What a Chain Link Fence Costs in San Bruno, CA
Plan on $3,500 – $9,000 for a full residential chain link fence in San Bruno. That range covers the fence itself, posts, concrete, gates, and labor. Five things push a job from the low end to the high end:
- Linear feet. A 100-foot back run sits near $3,500; a fully enclosed 250-foot lot with a drive gate lands near $9,000.
- Site conditions. Rocky soil, old concrete footings to demo, or a slope requiring stepped panels all add labor.
- Gates. One walk gate is standard. A double drive gate with heavier posts and hardware can add several hundred to over a thousand.
- Coating and gauge. Vinyl-coated 9-gauge runs higher per foot than bare 11-gauge.
- Permit scope. Height or placement that triggers review adds time and fees.
A written estimate lists post spacing, footing depth, gauge, coating, gate hardware, and demo – line by line, so you can compare bids fairly. It usually doesn’t cover stump removal, retaining walls to address grade, or relocating a sprinkler line; those get quoted separately once we see them. No-hassle upfront pricing means the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat San Bruno Homes Specifically Do to This Job
San Bruno’s housing stock shapes every fence we build here, because the city is really two stories side by side. In Crestmoor and the surrounding blocks, the 2010 PG&E gas pipeline explosion triggered a mandatory seismic retrofit and rebuilding wave that still drives permits and inspections today. Many of those post-WWII 1940s and 1950s homes were rebuilt or heavily retrofitted, so you’ll find newer, code-compliant lots beside older homes still working through foundation bolting and shear walling. For a fence, the practical result is a mix of clean, recently surveyed lines and older properties where the boundary is fuzzy and an old footing sits right where a new post wants to go.
The other local factor is the fog belt. San Bruno sits in that cool, damp marine layer with steady onshore wind off the Pacific, and wind load on a chain link run is real – posts spaced too far apart lean within a couple of seasons. We set posts in concrete at proper depth and tension the fabric correctly so the fence shrugs off the wind rather than working loose. Add the gas-line clearance procedures near the Crestmoor corridor, and a little patience at the locate stage pays off. When the fencing is part of a wider yard rebuild, it usually dovetails with Fence Installation in San Bruno work and often gets paired with Concrete Driveways & Concrete Work in San Bruno or Asphalt Driveways & Resurfacing in San Bruno so the gate and the driveway edge line up.
Serving San Bruno, CA – Our Local Coverage Area
We serve San Bruno and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Chain Link Fence in San Bruno
A standard residential chain link fence in San Bruno takes one to three days, with curing time between setting posts and hanging fabric. Most yards finish in a single visit; permit review or gas-line clearance near Crestmoor can extend the schedule. Call (866) 320-2646 and we’ll give you a firm timeline after the measure.
Not every chain link fence needs a permit, but height and placement near the property line can trigger review. Rather than guess, we check your specific lot before ordering material. Call (866) 320-2646 and we’ll walk you through what your job requires.
Yes, in most cases. We dig only at post locations and call 811 first, which protects buried utilities and irrigation lines, so we avoid the plumbing entirely whenever the layout allows. Call (866) 320-2646 for a site check.
Most chain link fence projects in San Bruno run $3,500 – $9,000 depending on length, gauge, coating, gates, and site conditions. Call (866) 320-2646 for an exact quote – estimates are free.
Every chain link fence we build is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right. Call (866) 320-2646 with any warranty question.
Get a Free Chain Link Fence Estimate in San Bruno
Ready to price a chain link fence in San Bruno? Call (866) 320-2646 and a live person answers any hour. We’ll set a free on-site measure, confirm your property line and utilities, and hand you a written line-item estimate – no change orders, no surprises. Our technicians have up to 12 years of experience, and every project is backed in writing.
Written by the team at Groundwork Construction Co.